Construction and Demolition, and how to guide - Civil Bites

  • Home
  • Construction and Demolition, and how to guide, approach to a circular economy.
Construction-and-Demolition-2

Construction and Demolition, and how to guide, approach to a circular economy.

September 30, 2022 Civil Bites 0 Comments

Introduction

Global urbanization has accelerated human population expansion in recent decades, requiring more material resources. Construction uses 32% of natural resources (Yeheyis et al., 2012). However, this figure is lower than in the 1990s (40%) (Rees, 2010); it is estimated that over 75% of building waste has a residual value and is not presently utilized or recycled. Insufficiently integrated waste management framework (Yeheyis et al., 2012). In general, construction and demolition wastes are everything that is no longer usable as a result of building, restoration, or destruction. Most of the time, such garbage is dumped. Construction and demolition trash (C&D waste) represent 30% of worldwide waste production (Papargyropoulou et al., 2011), with about 35% of construction and demolition (C&D) waste deposited in landfills yearly (Menegaki and Damigos, 2018). The construction sector has a substantial environmental effect due to natural resources, energy consumption, and trash creation. This is because the linear economic paradigm depends on the idea of taking, manufacturing, and discarding. Using energy-intensive equipment, raw materials are taken from natural resources and processed into building materials. Because most building materials cannot be deconstructed, they are either thrown into a landfill or burnt (Mangialardo and Micelli, 2018). The negative repercussions of construction and demolition (C&D) waste handling include environmental damage and public health (Lu and Yuan, 2012). This scenario necessitates an efficient framework to minimize pollution, climate change, and resource depletion (Yeheyis et al., 2012),7]. Concrete, wood, bricks, glass, steel, and other rejected materials are often found in C&D trash (Solís-Guzmán et al., 2009). Due to the huge amount of construction and demolition (C&D) waste generated each year, trash must be handled sustainably. Traditional environmental mitigation measures, such as linear economy, have been inefficient. For the concept of sustainable development, the term Circular Economy (CE) has arisen as a unique method to decrease negative environmental impacts while increasing economic growth. The Circular Economy (CE) is a unique reformative framework that helps optimize raw material use and guarantees material value throughout its lifespan (Bilal et al., 2020). Circular Economy (CE) also reduces trash output and conserves natural resources. This technique shows that everything created can be recycled, reconditioned, or utilized. In their conclusion, Hossain et al. (Hossain et al., 2020) stated that employing Circular Economy (CE) for construction and demolition (C&D) waste would improve sustainable resources, promote material efficiency by recycling/reusing construction waste, and reduce wasteful waste generation and disposal. Generally, the Circular Economy (CE) tries to repurpose materials that would otherwise be dumped into landfills in the construction business.

Different dimensions must be well understood to apply Circular Economy (CE) in a construction business properly. Ghisellini et al. studied the costs and advantages of Circular Economy (CE) in the building and demolition industry. Lederer et al. used a material flow analysis to establish how a Circular Economy (CE) may reduce raw mineral imports for the building industry in Vienna. They discovered that reusing/recycling building minerals might cut imports by 32%. Although various efforts have been made to recycle or recover construction and demolition (C&D) waste, little research has been done on the viability of including Circular Economy (CE) in the current built environment. Unlike small and medium-sized building projects, large-scale CE applications pose significant obstacles. Combining novel technologies, such as BIM (Building Information Modelling), with Circular Economy (CE) might alleviate the issues in large-scale built environments. Several techniques have been suggested to help the building industry migrate to Circular Economy (CE). Employing sustainable and durable materials, designing for disassembly, using modular and prefabricated pieces, and developing recovery methods [10,16]. However, little study has been done so far on the above methodologies.

This assessment will present a distinct viewpoint on how construction and demolition (C&D) waste may be repurposed by adopting a Circular Economy (CE) strategy. Unlike the linear economy, recovering or reusing resources requires additional stages, which means more obstacles. This research will explore the problems and limitations of implementing Circular Economy (CE) for construction and demolition (C&D) waste from a fresh perspective while minimizing environmental consequences and reducing carbon emissions. The prospective usage of several materials that have proved useful in building (especially concrete) will next be discussed. Also, this research provides a theoretical framework to encourage better use of recycled materials in the building or for other uses.

Materials and Methods

This study’s approach has two major stages. A systematic review was done to identify and synthesize scientific evidence in the first step. This method collects all essential research evidence. The biggest scientific database, Science Direct, gathered relevant material for the systematic review. Keywords included “construction and demolition”, “waste”, “construction”, “circular economy”, “framework”, “climate change”, “carbon emissions”, etc. The Boolean operators (AND) and (OR) were employed to retrieve relevant articles. A few examples include “circular economy” AND “framework,” “construction and demolition waste” AND “waste,” “construction and demolition” AND “strategies,” and so on. The search was restricted to 2005–2021, with most articles from the past five years. This aimed to guarantee the retrieval of unique ideas and research concepts that were relevant and original. The benefit of this work above prior publications is that it discusses the relevance of environmental repercussions based on construction and demolition (C&D) waste.

Construction-and-Demolition-3,Circular Economy
Construction-and-Demolition-2

English is a worldwide lingua franca and is commonly used for communication. Similarly, most of the sources included in this study were peer-reviewed studies in reputable, well-indexed journals. Some of the references came from citations in the literature. With this framework, early adoption of this successful strategy may be achieved.

Background Information

Waste

Garbage is an unavoidable by-product of production and usage, whether an industrial by-product or demolition waste. However, owing to pollution, resource depletion, landfill site shortages, and climate change, academics have started investigating society’s role in waste reduction [17,18].

Seadon argues that society’s ‘mine-build-discard’ mentality is unsustainable. According to the essay, unsustainable civilizations inevitably collapse. Successful communities recognize the value of limited resources, utilize them responsibly, and appreciate the surrounding environment. It is dynamic in all aspects, notably productivity, and uses scarce resources responsibly and effectively.

Globally, the quantity of garbage created each year is frightening. The global production of municipal solid garbage was 2.02 billion metric tonnes in 2016 and is expected to rise to 3.4 billion metric tonnes by 2050 (Tiseo, 2021). A 70% rise in worldwide garbage output is estimated if the existing system is maintained. To solve this situation, the world community must work together to safeguard the future prosperity of our children.

The New Zealand construction sector was expected to rise 70% by 2029 before the COVID-19 pandemic. This means more horizontal infrastructure projects for New Zealanders, which means more jobs (Harman, n.d.). As a result, building and demolition trash, which accounts for around half of New Zealand’s landfill garbage, is expected to rise, possibly straining the country’s waste management system. Recycling waste materials is one technique New Zealand’s construction sector may use to decrease its environmental impact. Concrete is one material that has been shown to benefit from the use of trash. According to Tavakoli et al. (Tavakoli, Hashempour and Heidari, 2018), Concrete is the most significant building material nowadays. He also claims that employing waste materials in concrete may considerably lessen the negative environmental consequences of concrete.

Concepts and Foundations of Circular Economy

Developing urban infrastructure has made sustainability a popular term and worry (Anastasiades et al., 2020). As a result, pollution and environmental damage increase (Jhatial et al., 2020). Sustainability is vital in every construction project since it helps both the project and the environment. Thus, a popular definition of sustainable development is the certainty that a project meets current requirements without jeopardizing future demands (Anastasiades et al., 2020). Sustainability has three pillars: planet, people, and profit. The planet’s ecosystem and environmental conditions are vital, but people’s demands should be met to maximize profit within limited resources. Sustainable development seeks to make growth socially, ecologically, and economically feasible, tolerable, and equitable.

The concept of Circular Economy (CE) arose from the desire to raise awareness about the environmental damage caused by the use and waste of raw resources. The Circular Economy (CE) is being investigated as a potential solution for natural resource depletion. The Circular Economy (CE) idea grew out of the 3Rs (Reduce-Reuse-Recycle). The 4R framework focuses on reducing, reusing, recycling, and recovering raw materials (Anastasiades et al., 2020). Unlike in the linear economy, raw materials in the Circular Economy (CE) are mended, recycled, and refurbished to be used in other processes. Thus, a Circular Economy’s principles include not buying surplus raw materials, changing design standards, and minimizing, reusing, and recycling trash. Such approaches effectively recycle, decrease trash, and prevent global environmental damage.

Figure 1 Flowchart of Material Use in Circular Economy

Construction Waste

Construction waste is categorized based on its origin or type. The writers defined trash as physical (residual debris) and non-physical (waste) (time overruns and cost overruns). Figure 2 investigates building waste sources. As indicated in Figure 2, building debris may be classified as either artificial or natural. Artificial sources include design, procurement, material handling, operation, residue, and other sources (ElHaggar, 2007). construction and demolition (C&D) waste materials are valuable and might be repurposed for concrete buildings. In concrete, the majority may be recycled as coarse or fine aggregate (Ulsen et al., 2013). Metals (6%), organic garbage (2%), glass and hazardous materials (2%), and miscellaneous (5%) (Ghorbanian et al., 2017).

Figure 3 shows the tonnes of building trash generated in major European nations and New Zealand. Construction trash is a major contributor in Denmark, France, Ireland, and Germany. Poland, Lithuania, Bulgaria, Greece, Slovakia, Hungary, and New Zealand generated the least building trash (Forbes, 2018). Construction and demolition waste accounts for over half of New Zealand’s yearly trash; hence it must be heavily engaged in waste reduction efforts (Ghorbanian et al., 2017). However, 2019 Auckland City Council research on the diversion of demolition trash indicated that recycling would still have substantial advantages (Rohani et al., 2019). The research focused on the cost-benefit analysis of reusing demolition trash for new dwellings. Opt A, a moderate deconstruction technique that emphasizes partial trash recovery and recycling; or Opt B, an intense deconstruction approach that emphasizes the two highest levels of the hierarchy. While the developers would only break even, the net benefits to society were large for both choices (A: NPV = $6.97 m, B: NPV = $14.46 m). Employers earned skills and experience through on-the-job training, while employees got skills and experience by reusing building materials. While reducing and reusing were proven to be better for society, recycling was also useful. For many materials, recycling is the sole option. Hence it is an integral waste reduction approach worth exploring.

Waste Minimization in the Circular Economy

The core of Circular Economy (CE) is reducing waste in landfills by reusing rejected materials in various ways. It is a 4R approach concentrating on Reduce-Reuse-Recycle-Recover raw material operations (Anastasiades et al., 2020). Less acquisition of raw materials means less GHG emissions, which helps both the economy and the environment. Moreover, reducing trash creation lowers the harmful consequences of garbage generation on our living environment.

Several studies have examined the economic viability of decreasing trash. This effort focuses on reducing construction and demolition (C&D) waste, which is the leading contributor to landfills worldwide (Osmani and Villoria-Sáez, 2019). A cost-benefit analysis conducted in Malaysia in 2006 revealed reducing construction and demolition (C&D) waste is possible with a 2.5% net profit (Begum et al., 2006). This research looked at the costs and advantages of reducing trash on a Malaysian construction site. The research showed several immediate advantages, including reduced purchase costs from reusing and recycling goods, reduced garbage collection and transport costs, and reduced disposal charges. Intangible advantages include decreased responsibility for environmental issues or worker safety, reduced soil and groundwater pollution risk, and better public perception of environmental issues. Direct expenditures for collection and separation, equipment purchases, storage, and transportation. Intangible expenses included worker health risks and negative externalities like noise and odor. According to Auckland City Council research, less waste is economically viable and has many unquantifiable advantages. According to both research, the rise in wastage levies might push construction businesses to adopt better waste reduction measures

An independent researcher did a cost-benefit study to evaluate the waste reduction hypothesis (Ghorbanian et al., 2017). The project included building a complicated model of a waste chain that appropriately represented society’s trash. This conceptual model stresses the complexity of waste reduction and explains prior global waste reduction challenges. According to the model, a high waste tax would increase net benefits for construction businesses and society, but it would also encourage the general people to dump their garbage unlawfully. It was decided that stiffer punishments should be implemented to counteract this issue. It was discovered that under the four billing systems, the expenses initially surpassed the benefits, but by the 11th month, the benefits started to outweigh the costs. The high-charge schemes also encouraged contractors to start trash management early, making it more effective. The net advantages increased considerably for reduced charge schemes when the regulation was tightened. To be effective, trash charges must be more than 76 yuan/ton ($15.50 NZD).

Waste reduction for contractors has been economically beneficial, as has waste minimization for recycling organizations. One research looked at the economics of recycled concrete aggregate (Tam, 2008). The cost-benefit study included both existing and concrete recycling methods for waste disposal. Using concrete debris as aggregates instead of dumping it in landfills may assist the building sector (Tam, 2008). The research indicated a $30,916,000 annual net gain and reduced resource depletion and energy use. Thus, building projects may be made eco-friendlier and more cost-effective. One issue was the lack of reclaimed concrete. Concrete is a seasonal waste product; thus, it was inconsistently used throughout the research, reducing profitability. Also, the recycling materials vary in size and the locations of ‘urban dumps’ change. Thus, recycling concrete is more challenging than maintaining a reliable cash source. Predictability is owing to a lack of material and price volatility.

As stated before, reducing waste is a difficult issue with many contributing elements. Van Tran interviewed seven experienced construction experts in 2017. These interviews were conducted to understand better the industry’s inadequate waste reduction practices. The present waste fee of $10 per tonne (2017), according to interviewees, is an inadequate incentive for construction enterprises to adopt better waste reduction plans. The existing levy has little impact on a company’s bottom line; therefore, it doesn’t motivate them to change. The levy charge would need to be hiked to $150 per tonne (Tran, 2017). In the model developed by Yuan et al. (Ding et al., 2015), a considerable rise in waste levies are required to observe meaningful change by contractors. This association is generally accepted as a waste reduction strategy. According to the interviewees, companies who do not decrease their trash should be penalized, not just financially.

Construction-and-Demolition-1,Circular Economy
Construction-and-Demolition-1

Advantages of Recycling of Construction Materials

The idea that our natural resources will someday become limited if people continue to mismanage and exploit them drives the usage of recycled materials in the building. Thus, the three pillars of sustainability, environment, economy, and society, will benefit (Khahro et al., 2021). Using recycled materials in the building has several benefits. Increasing the capacity to recycle and reuse building debris reduces the amount dumped in landfills, extending their useful life. Chemical additions in construction materials increase landfill contamination. Toxic contaminants may enter natural rivers and streams through groundwater intrusion. Increasing the use of recycled materials reduces the need to transport garbage from the building site to the landfill, lowering total CO2 emissions. There is a concern that eliminating landfill usage may result in job losses; nevertheless, new jobs can be created utilizing recycled materials. This is because recycled materials, unlike reused materials, will be modified to improve the secondary product while keeping their physical attributes to allow the material or product to perform its role in the structure. These procedures need skill sets, thereby creating job opportunities. Providing such chances will help the economy while also helping to lessen negative environmental repercussions. Population growth will raise the demand for land development. Increased recycling in the building sector reduces land conversion to landfills, making more quality land accessible for home development. Toxic compounds from building materials discarded in landfills wind up in rivers and natural streams. These unmanaged situations may affect the surrounding living species, endangering the community’s health. Due to heavy winds, bad scents from landfills may also be problems for adjacent communities.

Materials that can be Recycled

Concrete is a widely utilized building material that consumes limited resources and produces CO2. Using recycled materials reduces waste streams and production by-products. A 2018 assessment of the literature on these materials yielded encouraging findings (Tavakoli, Hashempour and Heidari, 2018). The research examined waste materials such as glass, plastic (PET), tile and ceramics, clay bricks, tires and rubber, metal, concrete, agricultural waste, silica fume, fly ash, etc. The research indicated that using trash in concrete, particularly aggregate, may minimize waste transfer to landfills. Using garbage in cement minimizes hazardous chemicals in concrete while also recycling. The review’s details are described here. Adding trash as an aggregate to concrete has several advantages. Glass may improve the characteristics of concrete. Glass may be crushed into three distinct forms: CGA, FGA, and Glass Powder (GP). A pozzolanic reaction occurs when glass is combined with cement, reducing CO2 and NO2 emissions (Ismail and AL-Hashmi, 2008). Glass has a higher thermal conductivity than aggregate; therefore, it may be utilized in structures that need thermal stability (Poutos et al., 2008). Combining coarse and fine glass improves water absorption and reduces shrinkage.

Plastic that may be utilized in concrete, PET, is considered environmentally friendly (Choi et al., 2005). Adding this plastic to concrete may boost its ductility and decrease shrinkage fractures (Singh, Shukla and Brown, 2004). The concrete is very lightweight yet is of good quality. Workability, density, modulus of elasticity, tensile strength, and slump are all reduced with lightweight concrete (Akçaözoğlu, Atiş and Akçaözoğlu, 2010). This aggregate is ideal for lightweight, corrosion-resistant concrete.

Tiles, marble, and ceramic are alternative aggregates that increase concrete characteristics. Using coarse ceramic granules (10–20%) enhances concrete compressive strength while decreasing specific weight without affecting water absorption. However, ceramics are porous and rigid; thus, water absorption and elasticity are weak. Tiles and ceramics are light and pozzolanic. Ceramics have qualities that vary depending on the manufacturing process and other factors. This may impair their performance in concrete; thus, they should be tested beforehand. Fired bricks may be used as sand in concrete. The research indicated that using clay bricks as sand might save money and time. Except for corrosion caused by steel reinforced bars, there were no detrimental consequences on the concrete. The concrete qualities provided no further advantages (Tavakoli, Hashempour and Heidari, 2018).

Tires and rubber are wastes with little recycling potential. Rubber in concrete solves this issue by lowering the rigidity of concrete and protecting it from fire. This research found an increase in flexural strength compared to the control group. While the brittleness of the control sample resulted in a fracture, the addition of the rubber fiber resulted in deformation but not collapse [59]. Silica flume mixed with cement paste and rubber particles enhanced compressive strength (Yehia and Emam, 2018). This fiber also increased freeze-thaw resistance. Rubber seems to be an excellent aggregate addition, but further study is needed to understand its strength and durability.

Given that 20–30% of agricultural output is trash, it is critical to maximizing recycling. Almond and coconut shells have been employed in a recent agricultural waste concrete study. According to one research, using almond shells as coarse aggregate resulted in a slump similar to normal concrete but with more air content. Another research used coconut shells to make lightweight, high-quality concrete. The lighter coarse grain aggregate possessed the same mechanical qualities as the heavier coarse grain aggregate. It had the same quality and flexural characteristics as the standard sample. The compressive strength of coconut shell concrete may be lowered by 22% by reducing the water-cement ratio. Concrete waste research started during WWII, making it the oldest recycled concrete material. The addition of fly ash to the mix helped reduce shrinkage caused by the concrete waste. Another research indicated that using clay brick powder as cement compensated for the waste aggregate’s compressive strength loss. The study shows that concrete waste may be utilized as an aggregate. However, various projects demand different concrete qualities, and the quantity of trash used can substantially alter the concrete performance.

17% of the material is slag (Tavakoli, Hashempour and Heidari, 2018). This by-product has a high shear modulus and chemical stability in alkaline and acidic conditions. Concrete mixed with slag had better water absorption, tensile and compressive strength. The slump increased with density and bending strength, as anticipated. Studies have demonstrated that ultra-strong concrete may be made at roughly 150 MPa. Steel furnace slag has a substantially greater hardness than typical aggregates, boosting flexural and compressive strength; yet, adding slag to concrete adds weight.

Because of its ‘super pozzolanic’ qualities, silica fume is a by-product of silica metal manufacturing. One research indicated that replacing 10–15% of the cement with silica powder enhanced early drying strength. Alternatively, another research finds silica flume may affect concrete durability. Because silica fume has various detrimental effects, it should only be used as required. Zhang et al. studied the impact resistance, mechanical characteristics, and durability of concrete containing coal fly ash. The authors observed that adding nano-silica (1–5% of the binder weight) improved the concrete’s mechanical characteristics and freezing-thawing resistance. The inclusion of nano-silica increased the samples’ compressive, flexural, and splitting tensile strengths by 15%, 27%, and 19%, respectively. Adding nano-silica to basalt fiber-modified recycled aggregate concrete is helpful. The addition of basalt fiber may prevent the development and spread of primary microcracks in recycled aggregate concrete and mortar. In this case, nano-silica fills microcracks and promotes cement hydration. Another study found that adding nano-silica to mortar may aid repolymerization; however, exceeding the critical ratio can adversely affect mechanical qualities.

Rice husk has excellent pozzolanic qualities when burnt, making it an ideal waste material for concrete. One research indicated that adding rice husk to a high-performance concrete containing micro silica reduced the cement’s porosity. Compressive strength and water absorption also improved. In addition to compressive strength and other mechanical qualities, resistance to chloride attack was certified. Rice husk may be utilized in high-strength concrete or repair mortars for nations with limited aggregate supply. To obtain the required qualities, it is necessary to employ rice husk as a cement addition at an appropriate amount.

Fly ash is a by-product of coal combustion. Using fly ash instead of cement for 40–60% of the cement resulted in a 28-day improvement in compressive strength. Also, pozzolanic fly ash has outstanding mechanical qualities, durability, and low chloride permeability (Uysal and Akyuncu, 2012). According to research, fly ash, unlike concrete debris and brick, does not degrade steel reinforcement. After 90 days, fly ash generates concrete with stronger compressive strength and water absorption than 10% glass powder. To decrease the harmful Alkali-Silica Reaction (ASR), silica should be added to the concrete as an additive.

Early ceramic tile chemistry analyses revealed pozzolanic characteristics. In one investigation, the utilization of clay brick waste in cement was 91 percent stronger than in regular concrete. The replacement cement also lowered concrete permeability and boosted efficiency. Alternatively, tile powder may be combined with silica flume to form concrete with comparable qualities (Tavakoli, Hashempour and Heidari, 2018).

CE for construction and demolition (C&D) Waste Paradigms and Model Strategies

A literature study indicated that research on circular economy and building in Australasia, notably New Zealand, is scarce. If Circular Economy (CE) is implemented in the building, environmental and economic difficulties may be minimized. A concept for integrating Circular Economy (CE) into the construction industry suggested that it may be done in three levels or stages: micro, meso, and macro. The authors believe that the micro stage of Circular Economy (CE) should concentrate on eco-friendly design and procedures and the meso level on waste trading networks. A collaborative industry with many stakeholders, for example, must cope with the 3R principles [102,103]. Only the UK and the Netherlands have Circular Economy (CE) in construction enterprises. For example, the UK has implemented Resource Efficient Construction, which lowers waste while simultaneously lowering GHG emissions. A questionnaire-based pilot study in Denmark found that the building process may move through the ReSOLVE framework’s share, optimize, and loop phases. In the Netherlands, the International Management Search Association (IMSA) is extremely active in incorporating Circular Economy (CE – Yumpu, n.d.). On-going waste, negative impacts on the planet’s ecosystem, illicit dumps of garbage, and lack of assistance from top building groups are all addressed in the proposed framework.

According to Esa et al., the 3Cs (contractor, consultant, and client) should be involved in the 3R operations of construction waste throughout the five phases of the project lifecycle: planning, designing, procurement, construction, and demolition. A micro-level industrialized building system (IBS) was recommended for effective and sustainable facility management. On a micro level, it was proposed that the building sector’s laws be implemented to reduce waste and promote sustainable growth. As total trash elimination is not practicable, authorities should control construction and demolition (C&D) waste via effective worker supervision. The model suggested by the authors includes this framework and the responsibilities of different stakeholders at various phases of the project lifecycle. The multiple waste reduction solutions listed above align with the 3R operations of effective construction and demolition (C&D) waste management.

Thoughts about Scientific Reuse

While adopting a circular economy in the construction and demolition (C&D) industry has many advantages, the scientific usage of such wastes must be researched. Contractors should be encouraged to recycle and reuse construction and demolition (C&D) waste materials, provided the recovery procedure results in a product of an acceptable grade as specified by specifications and is economically viable. Recycled waste materials’ chemistry, physical, mechanical, and durability properties must be studied. The environmental aspects of recycled materials include their sustainability and life cycle. Recycling is an energy-intensive process, but the benefits to society and the environment exceed the costs, making recycling economically viable. For example, in construction and demolition (C&D) waste recovery, energy is already spent on mining, quarrying, and transportation. This may also minimize emissions and other environmental problems, such as loss of natural resources and the spread of dust and airborne particles. However, life cycle analysis may be used to measure the contribution of Circular Economy (CE) to sustainability. Also, considering both hazardous and non-toxic environmental consequences, Butera et al. Transportation contribute the greatest (60–95%) to non-toxic consequences, the scientists found. Surprisingly, dumping minerals has less effect than using them. This is due to less leachate per tonne of construction and demolition (C&D) waste reaching groundwater resources over 100 years. A major feature of leaching oxyanions was identified to be soil Cr immobilization. Overall, leaching emissions influenced toxicity consequences more than manufacturing the same materials. The life cycle study indicated that transportation (on-site and off-site) absorbed 15% of CO2.

Conclusion

Annually, a considerable part of construction and demolition (C&D) trash ends up in landfills, causing severe environmental and socioeconomic issues. The volume of construction and demolition (C&D) waste dumped is increasing alarmingly, with detrimental repercussions. A few model practices currently exist to recover or reuse a tiny fraction of Circular Economy (CE) and construction and demolition (C&D) waste; nevertheless, worldwide adoption faces several challenges/barriers. The research shows that the problems fall into five categories: legal, technological, social, behavioral, and economical. Within the core areas, difficulties include legislation and regulations, permits and requirements, technology limitations, quality and performance, knowledge and information, and the expenses involved with early Circular Economy (CE) model adoption. The magnitude of problems also varies based on the project size and country. Thus, a basic framework and a practical method are required to shift from a linear to a circular economy in CDM. We must first investigate and categorize the financial and societal advantages of recycling construction and demolition (C&D) trash and the significant hurdles. Various integrative models and frameworks from the UK, Netherlands, Malaysia, Denmark, etc., were evaluated and debated. The feasibility and advantages of recycling building waste materials are examined in this review study. Previously published data on ecological, economic, and strength and durability were revealed. It was discovered that recycling waste materials in the building positively affect the environment, economy, and durability. Environmentally-friendly construction will also assist the government and stakeholders achieve sustainability objectives. The resources necessary to develop waste management strategies and execute them may also be reduced; nevertheless, the construction industry faces various obstacles that prohibit the recycling of construction and demolition (C&D) waste materials in building operations. Quality assurance systems, market uncertainty regarding waste materials availability and perceptions, and high costs of material recovery technologies were cited as barriers.

Reference list

Akçaözoğlu, S., Atiş, C.D. and Akçaözoğlu, K. (2010). An investigation on the use of shredded waste PET bottles as aggregate in lightweight concrete. Waste Management, [online] 30(2), pp.285–290. Available at: https://www.sciencedirect.com/science/article/pii/S0956053X09003870.

Anastasiades, K., Blom, J., Buyle, M. and Audenaert, A. (2020). Translating the circular economy to bridge construction: Lessons learned from a critical literature review. Renewable and Sustainable Energy Reviews, 117.

Begum, R.A., Siwar, C., Pereira, J.J. and Jaafar, A.H. (2006). The case of Malaysia is a benefit-cost analysis on the economic feasibility of construction waste minimization. Resources, Conservation and Recycling, [online] 48(1), pp.86–98. Available at: https://ukm.pure.elsevier.com/en/publications/a-benefit-cost-analysis-on-the-economic-feasibility-of-constructi.

Bilal, M., Khan, K.I.A., Thaheem, M.J. and Nasir, A.R. (2020). Current state and barriers to the circular economy in the building sector: Towards a mitigation framework. Journal of Cleaner Production, 276, p.123250.

Choi, Y.-W., Moon, D.-J., Chung, J.-S. and Cho, S.-K. (2005). Effects of waste PET bottles aggregate on the properties of concrete. Cement and Concrete Research, 35(4), pp.776–781.

Ding, Z., Wang, Y., Wang, H. and Wang, J. (2015). A Comparison Study of C&D Waste Management in Shenzhen and Hong Kong: A SWOT Perspective. pp.157–168.

ElHaggar, S. (2007). Sustainable Industrial Design and Waste Management: CradletoCradle for Sustainable Development.

Forbes, S. (2018). Construction and demolition waste piles up in the Super City. [online] interest.co.nz. Available at: https://www.interest.co.nz/property/101125/growing-auckland-producing-700000-tonnes-waste%C2%A0-year-construction-and-demolition#:~:text=A%20growing%20Auckland%20is%20producing [Accessed 24 Apr. 2022].

Ghisellini, P., Ripa, M. and Ulgiati, S. (2018). Exploring environmental and economic costs and benefits of a circular economy approach to the construction and demolition sector. A literature review. Journal of Cleaner Production, 178, pp.618–643.

Ghorbanian, T., Yousefi, N., Dadashzadeh, D., Khalili, F., Bagheri, A., Raei, M. and Mahvi, A. (2017). Quality and quantity of construction and demolition waste in Tehran. Journal of Environmental Health Science and Engineering, 15.

Harman, R. (n.d.). After the lockdown, here comes the biggest construction boom – ever. | Politik. [online] Available at: https://www.politik.co.nz/after-the-lockdown-here-comes-the-biggest-construction-boom-ever/ [Accessed 24 Apr. 2022].

Hossain, Md.U., Ng, S.T., Antwi-Afari, P. and Amor, B. (2020). Circular economy and the construction industry: Existing trends, challenges and prospective framework for sustainable construction. Renewable and Sustainable Energy Reviews, 130, p.109948.

Huang, B., Wang, X., Kua, H., Geng, Y., Bleischwitz, R. and Ren, J. (2018). Construction and demolition waste management in China through the 3R principle. Resources, Conservation and Recycling, 129, pp.36–44.

Ismail, Z.Z. and AL-Hashmi, E.A. (2008). Reuse of waste iron as a partial replacement of sand in concrete. Waste Management, 28(11), pp.2048–2053.

Jhatial, A.A., Goh, W.I., Mohamad, N., Rind, T.A. and Sandhu, A.R. (2020). Development of Thermal Insulating Lightweight Foamed Concrete Reinforced with Polypropylene Fibres. Arabian Journal for Science and Engineering, 45(5), pp.4067–4076.

Kabirifar, K., Mojtahedi, M., Changxin Wang, C. and Vivian W.Y., T. (2020). A conceptual foundation for effective construction and demolition waste management. Cleaner Engineering and Technology, 1, p.100019.

Khahro, S., Kumar, D., Siddiqui, F.H., Ali, T., Raza, M. and Khoso, A. (2021). Optimizing Energy Use, Cost and Carbon Emission through Building Information Modelling and a Sustainability Approach: A CaseStudy of a Hospital Building. Sustainability, 13.

Lederer, J., Gassner, A., Kleemann, F. and Fellner, J. (2020). Potentials for a circular economy of mineral construction materials and demolition waste in urban areas: a case study from Vienna. Resources, Conservation and Recycling, [online] 161, p.104942. Available at: https://www.sciencedirect.com/science/article/pii/S0921344920302603.

Lu, W. and Yuan, H. (2012). Title A framework for understanding waste management studies in construction.

Mangialardo, A. and Micelli, E. (2018). Rethinking the Construction Industry Under the Circular Economy: Principles and Case Studies. In: Green Energy and Technology. pp.333–344.

Menegaki, M. and Damigos, D. (2018). A review on current situation and challenges of construction and demolition waste management. Reuse and Recycling / UN SGDs: How can Sustainable Chemistry Contribute? / Green Chemistry in Education, [online] 13, pp.8–15. Available at: https://www.sciencedirect.com/science/article/pii/S245222361830018X.

Osmani, M. and Villoria-Sáez, P. (2019). Chapter 19 – Current and Emerging Construction Waste Management Status, Trends and Approaches. [online] ScienceDirect. Available at: https://www.sciencedirect.com/science/article/pii/B9780128150603000190.

Papargyropoulou, E., Preece, C., Padfield, R. and Abdullah, A. (2011). Sustainable construction waste management in Malaysia: a constructor’s perspective. Proceedings of the MISBE 2011International Conference on Management and Innovation for a Sustainable Built Environment.[Links].

Patwa, N., Sivarajah, U., Seetharaman, A., Sarkar, S., Maiti, K. and Hingorani, K. (2020). Towards a circular economy: An emerging economies context. Journal of Business Research, 122.

Poutos, K.H., Alani, A.M., Walden, P.J. and Sangha, C.M. (2008). Relative temperature changes within concrete made with recycled glass aggregate. Construction and Building Materials, 22(4), pp.557–565.

Rees, W. (2010). The built environment and the ecosphere: a global perspective. Building Research & Information, July 1, pp.206–220.

Rohani, M., Huang, T., Hoffman, L., Roberts, M. and Ribeiro, B. (2019). Cost Benefit Analysis of Construction and Demolition Waste Diversion from Landfill. A Case Study Based on HLC Ltd Development in Auckland.

Seadon, J.K. (2010). Sustainable waste management systems. Journal of Cleaner Production, 18(16-17), pp.1639–1651.

Singh, S., Shukla, A. and Brown, R. (2004). Pullout behavior of polypropylene fibers from the cementitious matrix. Cement and Concrete ResearchCEM CONCR RES, 34, pp.1919–1925.

Solís-Guzmán, J., Marrero, M., Montes-Delgado, M.V. and Ramírez-de-Arellano, A. (2009). A Spanish model for quantification and management of construction waste. Waste Management, 29(9), pp.2542–2548.

Tam, V.W.Y. (2008). Economic comparison of concrete recycling: A case study approach. Resources, Conservation and Recycling, 52(5), pp.821–828.

Tavakoli, D., Hashempour, M. and Heidari, A. (2018). Use of waste materials in concrete: A review. Pertanika Journal of Science and Technology, 26, pp.499–522.

Tiseo, I. (2021). Topic: Waste generation worldwide. [online] Statista. Available at: https://www.statista.com/topics/4983/waste-generation-worldwide/#dossierKeyfigures.

Tran, V.D. (2017). Evaluating the Economics of Construction and Demolition Waste Minimisation and Zero Waste in the New Zealand Construction Industry. [online] orapp.aut.ac.nz. Available at: http://orapp.aut.ac.nz/handle/10292/10538 [Accessed 24 Apr. 2022].

Ulsen, C., Kahn, H., Hawlitschek, G., Masini, E.A., Angulo, S.C. and John, V.M. (2013). Production of recycled sand from construction and demolition waste. Construction and Building Materials, 40, pp.1168–1173.

Uysal, M. and Akyuncu, V. (2012). Durability performance of concrete incorporating Class F and Class C fly ashes. Construction and Building Materials, 34, pp.170–178.

Won, J. and Cheng, J. (2017). Identifying potential opportunities of building information modeling for construction and demolition waste management and minimization. Automation in Construction, 79.

www.uncrd.or.jp. (n.d.). United Nations Centre for Regional Development (UNCRD). [online] Available at: https://www.uncrd.or.jp/content/documents/2669Parallelroundtable(2)-Presentation(2)-%20Weisheng%20Lu.pdf [Accessed 24 Apr. 2022].

Yeheyis, M., Hewage, K., Shahria, A.M., Eskicioglu, C., and Sadiq, R. (2012). An overview of construction and demolition waste management in Canada: A lifecycle analysis approach to sustainability. Clean Technologies and Environmental Policy, 15.

Yehia, S. and Emam, E. (2018). Experimental Study on Enhanced Crumb Rubber Concrete. International Journal of Scientific and Engineering Research, 9, pp.1240–1247.

Yumpu (n.d.). Unleashing the Power of the Circular Economy. [online] yumpu.com. Available at: https://www.yumpu.com/en/document/view/14610882/unleashing-the-power-of-the-circular-economy [Accessed 24 Apr. 2022].

leave a comment